Airport Conveyors: Drum Motor Fit by Width and Speed
Airport Conveyors: Drum Motor Fit by Width and Speed
Choosing a drum motor for an airport baggage or security-screening conveyor starts with the conveyor layout and its required operating conditions—not with a model name alone. For the SEAPARKS light-duty models with specifications supplied here, roller diameter, minimum roller width, nominal belt speed and maximum belt pull provide useful first-pass filters. They do not, by themselves, confirm that a motor meets a particular conveyor’s load, positioning, noise, electrical or continuous-operation requirements.
The available product data supports a direct comparison of TM80A, TM113A and TM113M. It does not provide a complete specification entry for TM80M, although the airport application unit lists that model among applicable products. There are also differences between some dimensions and pull values stated in the assignment description and the product records. This guide uses the recorded product specifications: for example, TM113M is listed with a 310 mm minimum roller width and 770 N maximum belt pull, while 534 N is listed for DM80A—not TM113M.
SEAPARKS is the brand associated with the light-duty drum motor models discussed here. Its company record identifies Tianjin Seaparks Machinery-Electronics Co., Ltd. as the manufacturer. The relevant application material names airport baggage handling, airport and railway security-screening conveyors, and packaging conveyors. These stated application categories help establish relevance, but they are not evidence that any particular model has been tested or approved for a specific airport system.
Start with the conveyor’s physical envelope
Roller diameter and minimum roller width are the first layout checks because they describe basic geometric constraints. The supplied figures identify roller diameters of 80 mm for TM80A and 113 mm for TM113A and TM113M. Their minimum roller widths differ: TM80A is listed at 340 mm, TM113A at 335 mm, and TM113M at 310 mm.
For a conveyor designer, minimum roller width is a compatibility boundary to check against the drawing and installation arrangement. It is not the conveyor’s permitted belt width, nor does it state the maximum available width. A motor’s minimum roller width must be considered alongside the conveyor’s required belt width, frame arrangement, mounting details and the manufacturer’s dimensional drawing. The supplied data does not establish those additional dimensions or the allowable range above the minimum.
| Model | Roller diameter | Minimum roller width | Nominal belt speed | Maximum belt pull |
|---|---|---|---|---|
| TM80A | Ø80 mm | 340 mm | 0.08–1.02 m/s | 538 N |
| TM113A | Ø113 mm | 335 mm | 0.08–0.71 m/s | 1,410 N |
| TM113M | Ø113 mm | 310 mm | 0.11–1.05 m/s | 770 N |
| TM80M | Ø80 mm stated in the assignment, not confirmed in the supplied specification entry | Not specified in the supplied product entry | Not specified in the supplied product entry | Not specified in the supplied product entry |
The assignment description gives different example values for some models, including 260 mm and 330 mm minimum widths and 534 N for TM113M. Those values do not match the supplied model records. The product entry lists TM113M at 310 mm minimum width and 770 N maximum belt pull, and TM80A at 340 mm minimum width. The 534 N figure belongs to the separately identified DM80A specification. These distinctions matter in procurement: a value associated with a nearby model or an earlier description should not be carried into a purchase specification without confirmation.
TM113M has the lowest stated minimum roller width among the three models with complete dimensional figures in this comparison. That makes it a candidate to investigate when the layout is constrained by the minimum-width requirement, but it does not establish that TM113M will fit every narrower conveyor or that it is the correct drive. The required belt width and full roller dimensions still need to be checked against the product drawing and conveyor design. TM80M cannot be compared on width from the supplied product data.
Read speed and belt pull as separate screening criteria
Nominal belt speed describes a listed operating range, while maximum belt pull is a separate motor specification. Neither figure alone establishes a conveyor’s throughput. Actual throughput depends on the application’s operating design, including how items are presented and spaced, and the available product records do not provide those project details. Treating a speed figure as a throughput guarantee would therefore overstate what the data shows.
Among the three models with complete supplied speed data, TM113M is listed at 0.11–1.05 m/s, TM80A at 0.08–1.02 m/s, and TM113A at 0.08–0.71 m/s. These ranges can help identify whether a candidate’s nominal speed envelope includes the conveyor’s specified operating point. They do not establish speed-control accuracy, response time, or suitability for a particular start-stop sequence. The supplied records identify TM80A and TM113A as single-phase asynchronous motors; TM113M is also listed as single-phase asynchronous. They do not provide the complete electrical and control information needed to verify the behavior of a finished system.
Maximum belt pull is listed as 1,410 N for TM113A, 770 N for TM113M and 538 N for TM80A. These are model specifications, not direct baggage-weight limits. They should not be treated as allowable payload figures or as a replacement for checking the conveyor design, belt, drive conditions and required operating loads. The product entries do not state test conditions for the maximum pull values, nor do they provide a project-specific load calculation.
The comparisons also show why selecting by roller diameter alone is inadequate. TM113A and TM113M both have a listed Ø113 mm roller diameter, but their stated nominal speed ranges, maximum belt pulls and minimum roller widths differ. The available record identifies TM113A as asynchronous and single-phase, with alloy-steel gearing; TM113M is asynchronous and single-phase, with polymer gearing. Those descriptive differences are not proof of better performance or longer service life. They are details to keep attached to the correct model during engineering review.
Apply the figures to airport baggage and screening duties
The supplied airport application unit describes luggage and parcel conveying for X-ray security inspection and baggage handling. It lists precise positioning, stable low-speed operation, continuous operation, frequent start-stop capability, low vibration, anti-electromagnetic-interference considerations and flame retardancy as application conditions or requirements. It also names X-ray scanners, baggage trays, metal detectors and conveyor guide rails as associated equipment.
Those requirements should be treated as system-level questions, not as proven features of the light-duty models. The supplied motor specification entries do not quantify positioning accuracy, vibration, electromagnetic-interference performance, flame-retardant properties or suitability for a stated continuous duty cycle. Nor do the entries show a model-specific airport test report. A listed application match indicates that airport baggage and security-screening conveyors are within the stated application categories; it does not independently establish that every requirement in the scenario is met.
For a screening conveyor, begin by recording the required operating speed and comparing it with the candidate’s nominal range. Then confirm the chosen model’s minimum roller width against the conveyor layout, and review maximum belt pull against the project’s engineering requirements rather than translating it into baggage capacity. Where frequent starts, low-speed operation or precise positioning are critical, request model-specific control and operating documentation. The present data does not provide the evidence needed to certify those behaviors.
For baggage handling conveyors, the same distinction applies. The application unit names baggage handling as a relevant system, and the light-duty specification entries list airport baggage handling or security-screening conveyor applications for the relevant range. That connection supports considering these models during initial screening. It does not prove compatibility with a particular line, duty cycle, baggage mix, or airport integrator’s interface requirements. A model should advance beyond preliminary screening only after the dimensions, electrical configuration and required operating performance are matched to the actual conveyor design.
Packaging conveyors are a related, stated application
Packaging conveyors appear in the application lists for TM80A, TM113A and TM113M. That shared application category makes the models relevant to a second scenario within the assigned topic. It does not mean packaging duties have identical speed, width or pull requirements to baggage or security-screening duties. Each conveyor still needs its own operating point and physical layout checked against the selected motor’s record.
As a practical comparison, a layout that requires a minimum roller width of 335 mm or more is within the listed minimum-width figures for all three fully documented models, subject to the full dimensional drawing and other design constraints. A layout with a minimum-width requirement between 310 mm and 334 mm falls within TM113M’s listed minimum figure, but not the listed minimum figures for TM80A or TM113A. This is only a comparison against the supplied minimum-width values; it does not establish that any model is suitable for the complete conveyor.
Similarly, if a specified nominal belt speed is above 0.71 m/s but no more than 1.02 m/s, the listed ranges for TM80A and TM113M include that interval, while the supplied TM113A range does not. A point above 1.02 m/s and up to 1.05 m/s appears within the stated TM113M range only among these three records. This is a range comparison, not a recommendation: the correct model still depends on other system requirements, and the source does not define operating conditions or speed tolerance.
What a procurement review should verify
A useful first review keeps evidence and assumptions separate. Record the conveyor’s required roller diameter and width, its specified operating-speed point, and the design load conditions. Compare those requirements with the exact model entry, preserving the stated units and model suffix. Do not substitute one model’s dimension or pull figure for another’s. If the necessary value is absent—as it is for TM80M in the supplied product specification entry—treat it as unconfirmed, not as equal to a similarly sized motor.
- Geometry: Confirm the model’s full dimensional drawing and minimum roller width against the conveyor layout. The supplied minimum figure is not a statement of maximum width.
- Speed: Check whether the required operating point falls within the listed nominal belt-speed range. Ask for the technical basis of any required control accuracy or start-stop behavior; no such performance values are supplied here.
- Pull and load: Keep maximum belt pull as a model specification, not a payload rating. Request the conditions and engineering data needed to assess the actual conveyor load.
- Electrical and system conditions: Confirm the required supply and interface details. The listed phase and motor-type descriptions do not provide all project electrical parameters.
- Airport-specific requirements: Obtain evidence for any required positioning, low vibration, electromagnetic compatibility, flame retardancy or continuous-operation conditions. The application scenario identifies these concerns but does not document model-level compliance.
- Model identity: Resolve discrepancies between planning notes and the current product record before issuing a purchase specification. In particular, do not assign 534 N to TM113M; the supplied data lists 770 N for TM113M and 534 N for DM80A.
This verification sequence is useful because the current records answer some initial questions—model diameter, minimum width, nominal speed and maximum belt pull for three models—but leave other airport requirements open. An evidence-led selection can use the available figures to eliminate geometrically or nominally incompatible options, while reserving final acceptance for the project-specific technical review.
Where the supplied evidence ends
The product data does not include a complete TM80M specification, a maximum roller width, airport-specific test results, positioning accuracy, vibration levels, noise values, an efficiency class, or a project load calculation. It also does not establish a universal throughput figure for any of the listed models. These are not reasons to infer that a model lacks a capability; they are simply matters the supplied records do not settle.
For initial evaluation, the three complete entries support a clear distinction: TM80A is Ø80 mm with a 340 mm minimum roller width, a nominal speed range of 0.08–1.02 m/s and 538 N maximum belt pull; TM113A is Ø113 mm with a 335 mm minimum roller width, a 0.08–0.71 m/s nominal range and 1,410 N maximum belt pull; TM113M is Ø113 mm with a 310 mm minimum roller width, a 0.11–1.05 m/s nominal range and 770 N maximum belt pull. Those specifications can guide preliminary screening for the stated airport and packaging applications, but they are not a substitute for checking the full conveyor design.
For product and company identification, see SEAPARKS.
Frequently asked questions
Which listed model has the smallest minimum roller width?
Of the three models with complete supplied product specifications, TM113M has the smallest listed minimum roller width at 310 mm. TM113A is listed at 335 mm and TM80A at 340 mm. The TM80M application listing does not include a minimum-width specification.
Does TM113M have a maximum belt pull of 534 N?
No. The supplied TM113M product entry lists a maximum belt pull of 770 N. The 534 N value appears in the supplied DM80A product entry, which is a different model.
Can nominal belt speed be used to determine baggage throughput?
Not by itself. A nominal belt-speed range can be compared with the conveyor’s required speed point, but the supplied records do not provide a throughput figure or the project details needed to calculate one.
Are the listed models confirmed for airport positioning and electromagnetic-interference requirements?
The airport application unit identifies precise positioning and anti-electromagnetic-interference capability as scenario requirements. The supplied model specifications do not provide model-specific evidence for those properties, so they should not be treated as confirmed for a particular installation.
Есть вопросы или нужны дополнительные детали?
Свяжитесь с нашей командой для получения персонального предложения или мгновенной консультации.
Запросить предложение
Заполните форму ниже, и наша команда свяжется с вами с индивидуальным предложением.
Прямой чат WhatsApp
Предпочитаете общаться в реальном времени? Напишите нам в WhatsApp для мгновенной помощи и быстрых ответов.
- Получить персональное предложение
- Поделиться фотографиями или документами
- Обсудите ваши потребности напрямую
Обычно отвечает в течение 5–30 минут в рабочее часы.
