{{ variable.name }}
Anti-vibration structure | noise at or below 75 dB(A) | MTBF up to 30,000 h | sealed housing for narrow underframes
This GCU11 variant is built for rail transit air supply, where the unit runs continuously under high vibration, tunnel dust and frequent start-stop and sits in a very tight underframe bay. The anti-vibration integrated structure carries the airend, separator tank, three filters and four valves in one sealed body of 378 x 350 x 415 mm and 55 kg, which fits the narrow space under a metro or EMU floor. Noise is held at or below 75 dB(A) and measured mean time between failures reaches 30,000 h in the rolling stock programme. Brake pipe pressure is supplied between 5 and 16 bar with a 0.6-1.0 m3/min delivery at 7 bar across a 4-7.5 kW drive range.

The block is developed for continuous running under rail vibration, keeping air supply stable on EMU and metro bogie-mounted air systems.
Measured reliability in the rolling stock programme reaches 30,000 h between failures, which supports long maintenance intervals for fleet operators.
A 55 kg body of 378 x 350 x 415 mm fits underframe envelopes where a conventional airend plus receiver would not go.
Low noise output reduces the acoustic treatment needed around brake and auxiliary air supply packages in passenger areas.
A patented anti-emulsification method (CNIPA patent ZL2025 1 1888313X) combined with triple-sealing technology addresses the condensation that causes oil emulsification and leakage.
Built-in coarse separation plus an oversized external fine separator protect brake control units and dryers downstream.
| Model | GCU11 rail transit configuration |
|---|---|
| Structure | Anti-vibration integrated 9-in-1 housing, sealed |
| MTBF | Up to 30,000 h in rolling stock service |
| Noise | At or below 75 dB(A) |
| Power | 4-7.5 kW |
| Speed | 2900-6500 rpm |
| Free air delivery at 7 bar | 0.6-1.0 m3/min |
| Working pressure, max / min | 16 / 5 bar |
| Max discharge temperature | 105 C |
| Oil carry-over | Below 2 ppm (design at or below 3 ppm) |
| Net weight | 55 kg |
| Dimensions (L x W x H) | 378 x 350 x 415 mm, excluding air filter assembly |
| Housing / rotors | High-grade cast iron housing, forged alloy steel rotors with UV patented profile |
| Bearings / shaft seal | SKF heavy-duty rolling bearings, triple-sealing technology |
Rail configurations are selected by vehicle type and by the air consumer: brake pipe, pantograph assist or air suspension. Power stays within 4-7.5 kW and speed within 2900-6500 rpm, so the delivery point can be aligned with the brake control unit demand. For 16 bar duty the external fine separator, oil filter and safety valve are specified at 20 bar rating or higher. Where an imported airend is being replaced, drop-in replacement dimensions can be quoted.
The housing is high-grade cast iron, with an aluminium-alloy version under development. Rotors are forged alloy steel machined to the German-designed UV patented profile over more than 20 precision steps to micron-level accuracy, carried in SKF heavy-duty rolling bearings. The shaft seal applies triple-sealing technology, and the anti-oil-emulsification method is protected under CNIPA patent ZL2025 1 1888313X with PCT filing available on request. Four valves and three filter positions are integrated on the block, and the sealed housing closes the assembly against tunnel dust.

Rail projects are configured around the vehicle interface: mounting points, port positions, pressure setting and the connection to the brake control unit and main reservoir. Drawings are supplied for approval before series build, and the sealed housing can be adapted to the available underframe envelope. Fleet programmes can be supported with a documented maintenance scope limited to filter replacement where the application allows.
A metro operator has approximately 120 units in service for four years on metro train brake and air suspension supply. There has been zero oil-emulsification or leakage failure since commissioning, and maintenance has been limited to filter replacement. The sealed integrated housing fits the narrow underframe of the fleet.
A rolling stock OEM has taken approximately 400 units per year for five years for EMU and metro braking and auxiliary air supply. Localised replacement of imported airends reduced total cost by over 30 percent, air supply stays stable under high vibration, and MTBF reaches 30,000 h. A locomotive manufacturer has also used the series for five years as main air source on locomotive and rail vehicle wind source systems, supported by rail transit product certification.
How is vibration handled on a rail vehicle?
The unit uses an anti-vibration integrated structure developed in rolling stock programmes, and air supply has remained stable under high vibration in the EMU and metro applications.
What maintenance interval can be expected?
MTBF reaches 30,000 h in rolling stock service. In the metro fleet of approximately 120 units, maintenance over four years has been limited to filter replacement.
Will the unit fit a narrow underframe bay?
The sealed integrated housing measures 378 x 350 x 415 mm excluding the air filter assembly at 55 kg, and it was selected for a metro fleet specifically because it fits the narrow underframe.
How is oil emulsification prevented?
The anti-oil-emulsification method is protected under CNIPA patent ZL2025 1 1888313X, combined with triple-sealing technology on the shaft and two-stage oil separation.
Which rail approvals are held?
The company holds rail transit product certification for air supply units used on locomotives, EMU, metro and freight trains, plus CE certification from TUV Rheinland, ISO 9001:2015 from SGS and IATF 16949.
What noise level is quoted?
Noise is at or below 75 dB(A), which is the figure used for rail transit packages in this series.
Send the vehicle type, underframe envelope and brake system pressure so the rail configuration can be confirmed.
Email: service@woyo.cn | Tel: +86 510 8599 6655 | WhatsApp: +86 189 1237 9878
Wuxi Woyo Superdo Compressor Co., Ltd. (WOLXAIR), No.5 Changkang Road, Mashan, Binhu District, Wuxi, Jiangsu, China